Automatic Drum sand blasting machine sandblaster with factory price-Tianfuchenglai-3-8

I.      Application

According to the characteristics of products which the customers with specially designed belt conveyor automatic sandblasting machine, sandblasting surface is used for cookware utensils and appliances, can remove combination, flow lines and die marks,etc; Otherwise it can satisfy deburring, oxide skin, surface finishing, electroplating or spray pretreatment and other technical requirements.

II.    The main technical parameters

1. Cleaning products

（1）Width    1150mm

（2）Height    250mm

（3）Length    2000mm

2. Conveyor system

（1）Working speed    0.3-5m/min（Frequency adjustment）

（2）Power    1.5kw×1set

（3）Speed ratio   1：100

（4）Transmission v belt  B-Type（6600mm*L）

3. Spray gun

（1）Model  DS-B                  （2）Abrasive shot speed  75-100m/s

（3）Nozzle diameter  φ8mm*80     （4）Pressure  3-8barr

（5）Number of guns 12pcs     （6）Swing speed 10-94times(Frequency adjustment)

 (7) Power  400W               （8）Speed ratio     1:15

4. Segregator

(1) Separation volume    5t/h     (2) Separation zone wind speed    4-5m/s

5. Dust removal system（1Set）

(1) Dust collector

a、Model 1212-4   

b、Air volume 2504m³/h

c、Core φ320*660

(2) Centrifugal fan

a、Model 9-19Type，A type transmission        b、Air volume 2504m³/h

c、Wind pressure of work 4112MPa              d、Power 7.5kw

6. Full engine power: 11kw

7. Total air rate volume 2504m³/h

8. Overall machine dimension

(1) Max overall dimension: 4100mm×1600mm×3100mm

III.  Structural adjustment and adjustment installation

This machine is a high-performance V-belt conveyor sandblasting cleaning equipment, in the process of cleaning by motor drive worm gear and worm reducer, Towing V-belt conveyor system to the work piece to clean room, and spraying by a all-around of 12 guns, making their oxidation scales and dust’s away quickly, obtaining with certain roughness of the bright surface, at the same time work piece is suffered from strong impact, eliminated the stress of work piece, to avoid deformation. During the cleaning process, falling mixture of dust scattered is collected directly by the set of sand bucket, by the dust removal fan suck in suction separator, after the dust separator was separated，abrasive sand goes to the storage tank，dust is driven by fans, through the air duct pipe system, and with filters precipitator dust, efficiency can reach 99%, after purification, the air emissions into the air.

This device has the following several parts: Sandblasting main engine, Belt conveyor system, Segregator, Dust removal system, Electrical Control System.

1. Sandblasting main engine

(1) Structure principle

The master consists of three parts cleaning room, inlet room, and discharge room.

A、Clean room is installed 12 spray guns, this space structure is passed CAD test and actual verification, can achieve best to clean up the work piece.

B、Cleaning room is semi-enclosed, equipped with steel and rubber curtain shield to prevent abrasive flying, while room has some negative pressure to prevent the escape of dust.

C、Cleaning room is equipped with rubber inside body, protect the chamber wall plate from wear and tear, extending the service life; In the cleaning of cone set sand bucket is equipped with the network, to block sundries, protect the nozzle, easy to repair.

(2) Adjust the application and maintenance

A、Cleaning room protection room and package cast nuts are wearing parts. Must check the degree of wear and change in time, pay attention to install guard plates lap joint, to prevent damage to the wall and endanger safety.

B、Cleaning room rubber curtain are wearing parts should be replaced if damaged.

C、Must cut off the power for maintenance, listing alerts, non-powered operation, and offenders will be could endanger life safety.

2. Belt conveyor system

（1）Structure principle

The conveying system consists of v belt, master-slave shaft, cycloid reducer and three-phase asynchronous motor, the system is stable and running speed can be controlled by the frequency converter.

（2）Adjustment and application

According to the work piece cleaning efficiency, adjust the speed of the conveyor system; from low speed to high speed slowly adjust, in order to achieve high quality cleaning efficiency and good economic performance.

3. Separator

（1）Structure principle

The separator is a cyclone dust mixture was inhaled by back sand tube to the sand separator, by sharing in formation of the cyclone, the walls of the abrasive to jilt to the separator after free fall into the recycling in the store sandbox, dust is inhalation of dust removal system, pure gases into the air after purification treatment, become trapped particles of dust collection.

（2）Adjustment and application

A、The above screw on regulator separator to change the starting position within the cyclone separator to obtain optimum separation.

B、Separator outlet pipe connection with dust removal system, guarantee the dust into the dust collection box.

4. Dust removal system

（1）Structure principle

Filter dust collector contains High efficiency filter，Back flushing filters body，Centrifugal fans，Dust hopper，Engine body，Air hose，air duct elbow.

A、The body by 3 mm high quality low carbon steel plate welded together, both inside and outside surface spray treatment.

Overall Size：1200×1200×2000(mm).

B、High efficiency filterφ320×660，total 4 pcs. It is for dust removal process, purification effect accord with national environmental standards。It is made of 100% polyester fiber material, the thickness of 0.7 mm, 10 um porosity, gas resistance 2.98 mbar (guarantee for 40 cm/s air velocity, the pressure needed to 2.98 mm water column), heat resistance capacity of up to 130 degrees.

C、Centrifugal fan type 9-19, A-transmission, power: 7.5 KW, speed:2900R/min

D、Back flushing filters body contains the air tank, pulse electromagnetic valve, pipe and other components.

E、Dust hopper is welded 3mm high quality low carbon steel plate, the surface paint treatment. Overall Size：400×400×300(mm).

F、Air hose is jointed with PVC pipes.

G、Cleaning method: vibrating pulse cleaning.

（2）Adjustment and application

 Vibration pulse cleaning time can be adjusted by pulse controller.