facebook
5%OFF

Competitive price for Automatic conveyor sandblasting machine from Chinese factory supply with factory price-Tianfuchenglai-3-2

stars, based on 0reviews
Ch$29392500.00nowCh$27922875.00 unit
1items available
Contact Us
Description

Automatic conveyor sandblasting machine

Sandblasting machine

I.      Application

According to the characteristics of products which the customers with specially designed belt conveyor automatic sandblasting machine, sandblasting surface is used for cookware utensils and appliances, can remove combination, flow lines and die marks,etc; Otherwise it can satisfy deburring, oxide skin, surface finishing, electroplating or spray pretreatment and other technical requirements.

II.    The main technical parameters

1. Cleaning products

1Width    1150mm

2Height    250mm

3Length    2000mm

 

2. Conveyor system

1Working speed    0.3-5m/minFrequency adjustment

2Power    1.5kw×1set

3Speed ratio   1100

4Transmission v belt  B-Type6600mm*L

 

3. Spray gun

1Model  DS-B                  2Abrasive shot speed  75-100m/s

3Nozzle diameter  φ8mm*80     4Pressure  3-8barr

5Number of guns 12pcs     6Swing speed 10-94times(Frequency adjustment)

 (7) Power  400W               8Speed ratio     1:15

 

4. Segregator

(1) Separation volume    5t/h     (2) Separation zone wind speed    4-5m/s

 

5. Dust removal system1Set

(1) Dust collector

aModel 1212-4   

bAir volume 2504m3/h

cCore φ320*660

 

(2) Centrifugal fan

aModel 9-19TypeA type transmission        bAir volume 2504m3/h

cWind pressure of work 4112MPa              dPower 7.5kw

 

6. Full engine power: 11kw

 

7. Total air rate volume 2504m3/h

 

8. Overall machine dimension

(1) Max overall dimension: 4100mm×1600mm×3100mm

 

III.  Structural adjustment and adjustment installation

This machine is a high-performance V-belt conveyor sandblasting cleaning equipment, in the process of cleaning by motor drive worm gear and worm reducer, Towing V-belt conveyor system to the work piece to clean room, and spraying by a all-around of 12 guns, making their oxidation scales and dust’s away quickly, obtaining with certain roughness of the bright surface, at the same time work piece is suffered from strong impact, eliminated the stress of work piece, to avoid deformation. During the cleaning process, falling mixture of dust scattered is collected directly by the set of sand bucket, by the dust removal fan suck in suction separator, after the dust separator was separatedabrasive sand goes to the storage tankdust is driven by fans, through the air duct pipe system, and with filters precipitator dust, efficiency can reach 99%, after purification, the air emissions into the air.

 

This device has the following several parts: Sandblasting main engine, Belt conveyor system, Segregator, Dust removal system, Electrical Control System.

 

1. Sandblasting main engine

(1) Structure principle

The master consists of three parts cleaning room, inlet room, and discharge room.

AClean room is installed 12 spray guns, this space structure is passed CAD test and actual verification, can achieve best to clean up the work piece.

BCleaning room is semi-enclosed, equipped with steel and rubber curtain shield to prevent abrasive flying, while room has some negative pressure to prevent the escape of dust.

CCleaning room is equipped with rubber inside body, protect the chamber wall plate from wear and tear, extending the service life; In the cleaning of cone set sand bucket is equipped with the network, to block sundries, protect the nozzle, easy to repair.

 

(2) Adjust the application and maintenance

ACleaning room protection room and package cast nuts are wearing parts. Must check the degree of wear and change in time, pay attention to install guard plates lap joint, to prevent damage to the wall and endanger safety.

BCleaning room rubber curtain are wearing parts should be replaced if damaged.

CMust cut off the power for maintenance, listing alerts, non-powered operation, and offenders will be could endanger life safety.

 Automatic Sandblasting 

The operator put or fix the workpiece on the conveyor belt,when the workpiece is transported into the sandblasting chamber,the

blasting guns automatically swinging and blasting,ensures the products is blasted entirely.The the workpiece pass through the

clean room for cleaning,finally comes out from the other side of the conveyor to be discharged.

Competitive price for Automatic conveyor sandblasting machine from Chinese factory supply with factory price-Tianfuchenglai-3-2 Competitive price for Automatic conveyor sandblasting machine from Chinese factory supply-Tianfuchenglai-3-2

Best sellers