Silicon carbide crucible and melting furnace
High temperature coating curing oven machine
Ultrasonic/high pressure cleaning and drying machine line
Cold Chamber Die Casting machine
Hydraulic Press Machine & CNC machine
Automatic Sandblasting Blaster Machine
Steel coil slitting machine
Other machine line
Automatic horizontal pass-type sandblasting machine with factory price-Tianfuchenglai-3-15
Automatic horizontal pass-type sandblasting machine
Continuous pass through type shot blast sandblasting machine
According to the characteristics of products which the customers with specially designed belt conveyor automatic sandblasting machine, sandblasting surface is used for cookware utensils and appliances, can remove combination, flow lines and die marks,etc; Otherwise it can satisfy deburring, oxide skin, surface finishing, electroplating or spray pretreatment and other technical requirements.
II. The main technical parameters
1. Cleaning products
2. Conveyor system
（1）Working speed 0.3-5m/min（Frequency adjustment）
（3）Speed ratio 1：100
（4）Transmission v belt B-Type（6600mm*L）
3. Spray gun
（1）Model DS-B （2）Abrasive shot speed 75-100m/s
（3）Nozzle diameter φ8mm*80 （4）Pressure 3-8barr
（5）Number of guns 12pcs （6）Swing speed 10-94times(Frequency adjustment)
(7) Power 400W （8）Speed ratio 1:15
(1) Separation volume 5t/h (2) Separation zone wind speed 4-5m/s
5. Dust removal system（1Set）
(1) Dust collector
b、Air volume 2504m3/h
(2) Centrifugal fan
a、Model 9-19Type，A type transmission b、Air volume 2504m3/h
c、Wind pressure of work 4112MPa d、Power 7.5kw
6. Full engine power: 11kw
7. Total air rate volume 2504m3/h
8. Overall machine dimension
(1) Max overall dimension: 4100mm×1600mm×3100mm
III. Structural adjustment and adjustment installation
This machine is a high-performance V-belt conveyor sandblasting cleaning equipment, in the process of cleaning by motor drive worm gear and worm reducer, Towing V-belt conveyor system to the work piece to clean room, and spraying by a all-around of 12 guns, making their oxidation scales and dust’s away quickly, obtaining with certain roughness of the bright surface, at the same time work piece is suffered from strong impact, eliminated the stress of work piece, to avoid deformation. During the cleaning process, falling mixture of dust scattered is collected directly by the set of sand bucket, by the dust removal fan suck in suction separator, after the dust separator was separated，abrasive sand goes to the storage tank，dust is driven by fans, through the air duct pipe system, and with filters precipitator dust, efficiency can reach 99%, after purification, the air emissions into the air.
This device has the following several parts: Sandblasting main engine, Belt conveyor system, Segregator, Dust removal system, Electrical Control System.
1. Sandblasting main engine
(1) Structure principle
The master consists of three parts cleaning room, inlet room, and discharge room.
A、Clean room is installed 12 spray guns, this space structure is passed CAD test and actual verification, can achieve best to clean up the work piece.
B、Cleaning room is semi-enclosed, equipped with steel and rubber curtain shield to prevent abrasive flying, while room has some negative pressure to prevent the escape of dust.
C、Cleaning room is equipped with rubber inside body, protect the chamber wall plate from wear and tear, extending the service life; In the cleaning of cone set sand bucket is equipped with the network, to block sundries, protect the nozzle, easy to repair.
(2) Adjust the application and maintenance
A、Cleaning room protection room and package cast nuts are wearing parts. Must check the degree of wear and change in time, pay attention to install guard plates lap joint, to prevent damage to the wall and endanger safety.
B、Cleaning room rubber curtain are wearing parts should be replaced if damaged.
C、Must cut off the power for maintenance, listing alerts, non-powered operation, and offenders will be could endanger life safety.
2. Belt conveyor system
The conveying system consists of v belt, master-slave shaft, cycloid reducer and three-phase asynchronous motor, the system is stable and running speed can be controlled by the frequency converter.
（2）Adjustment and application
According to the work piece cleaning efficiency, adjust the speed of the conveyor system; from low speed to high speed slowly adjust, in order to achieve high quality cleaning efficiency and good economic performance.
The separator is a cyclone dust mixture was inhaled by back sand tube to the sand separator, by sharing in formation of the cyclone, the walls of the abrasive to jilt to the separator after free fall into the recycling in the store sandbox, dust is inhalation of dust removal system, pure gases into the air after purification treatment, become trapped particles of dust collection.
（2）Adjustment and application
A、The above screw on regulator separator to change the starting position within the cyclone separator to obtain optimum separation.
B、Separator outlet pipe connection with dust removal system, guarantee the dust into the dust collection box.
4. Dust removal system
Filter dust collector contains High efficiency filter，Back flushing filters body，Centrifugal fans，Dust hopper，Engine body，Air hose，air duct elbow.
A、The body by 3 mm high quality low carbon steel plate welded together, both inside and outside surface spray treatment.
B、High efficiency filterφ320×660，total 4 pcs. It is for dust removal process, purification effect accord with national environmental standards。It is made of 100% polyester fiber material, the thickness of 0.7 mm, 10 um porosity, gas resistance 2.98 mbar (guarantee for 40 cm/s air velocity, the pressure needed to 2.98 mm water column), heat resistance capacity of up to 130 degrees.
C、Centrifugal fan type 9-19, A-transmission, power: 7.5 KW, speed:2900R/min
D、Back flushing filters body contains the air tank, pulse electromagnetic valve, pipe and other components.
E、Dust hopper is welded 3mm high quality low carbon steel plate, the surface paint treatment. Overall Size：400×400×300(mm).
F、Air hose is jointed with PVC pipes.
G、Cleaning method: vibrating pulse cleaning.
（2）Adjustment and application
Vibration pulse cleaning time can be adjusted by pulse controller.
IV. Electrical system
A. General technical requirements
The main circuit adopts the 380V electric equipment, control circuit use the 220V，in order to facilitate the operation and maintenance, the electrical equipment is installed in the centralized control box, controls the motors and solenoid valve opening stop.
2. Control object
（1）Dust removal fan 7.5kw 1set
（2）Conveyor motor 1.5kw 1set
（3）Spray gun swing motor 0.4kw 1set
（4）Headlamp 9w 2pcs
（5）Electromagnetic valve 12pcs
B. Monitoring and instructions
1. Motor normal operation and stop，green and red light indicates；
2. Transmission, spray gun swing speeds adjust respectively by two inverter instructions.
C. The main electrical interlock
1. Gun with door interlock, two doors must be closed on the host, then the gun to start.
D. Electrical operating instructions
1. Close the main power switch, power on, power bright lights;
2. Adjusting the spray gun pressure, manual/automatic switch, move automatically after the start, follow these steps in turn:
Dust removal system→ Belt conveyor system→ Spray gun swing→ Spray gun start
After the work piece is finished, click Close in the following turns:
Spray gun stop→Swing stop→Conveyor belt Stop→Dust removal system stop
For details, please follow our engineer to install operation guide, this sequence of operations described only a brief introduction, for reference only.
In order to easy for transportation, it will be shipped by Packet transport, When the user installation, depends on the situation to do adjustment.
VI. Operating procedures
Inspection for machine equipment before working: Checking the spray gun nozzle, sand tubes, protective rubber wear circumstances before the operation, if found that situation should be promptly reported to be replaced. Before starting the machine to make sure main engine two doors are closed. Operation processes, check electrical instructions.
VII.Maintenance, security and troubleshooting
1. Care and maintenance
A、The machine should be checked regularly, pay attention to maintenance and regular cleaning.
B、When servicing are strictly prohibited to left tools, screws and other debris in the machine.
C、When the machine is in operation separator, filter regularly remove waste, ensure the normal operation.
2. Check the operation of the machine before and after
A、 Before the operation, check the spray guns, sand tubes, rubber curtains and other wearing parts circumstances, pay attention to the timely replacement.
B、Check all the moving parts, bolted joints loose or not, if loose should be tightened in time.
C、Check whether have debris falling into the machine, if have should be cleared in time to prevent blocking.
D、To operate correctly in accordance with electrical codes.
3. Operation inspection
Operation should always check the cleaning quality of the work piece, adjust the angle of spray gun and the work piece conveying speed if necessary.
A、Non-operating and maintenance personnel can not operate.
B、Should be cut off power supply, maintenance and hang warning mark in the eye-catching place.
C、Rubber curtains and dust collector to avoid fire.
D、During operation of the machine, protective cover and others must be installed securely.
E、When power outage occurs, to cut off the electrical power supply.
Cheap price for Aluminium scrap foil melting crucible copper melting machine-Tianfuchenglai-75-7-1
$865.00now $835.00 piece3%OFF
Best Price High Temperature Silicon Carbide Crucible furnace Graphite Crucible for Melting aluminum copper-Tianfuchenglai-75-9-1
$1150.00now $1050.00 piece9%OFF
Best price for Underground furnace melting crucible-Silicon carbide crucible with factory price-Tianfuchenglai-75-13-1
$400.00now $350.00 piece12%OFF
Factory supply crucible melting aluminum scrap making aluminum ingots-Tianfuchenglai-75-10-1
$880.00now $820.00 piece7%OFF
Factory price for silicon carbide crucible melting copper brass wire cable for brass ingots-Tianfuchenglai-75-11-1
$80.00now $60.00 piece25%OFF
Gold silver melting crucible-graphite crucible furnace use electric power supply with factory price -Tianfuchenglai-75-12
$75.00now $55.00 piece27%OFF
New technology silicon carbide crucible melting copper brass wire cable for brass ingots-Tianfuchenglai-75-11
$80.00now $60.00 piece25%OFF
Industrial Tyre oil power supply crucible melting aluminum scrap making aluminum ingots with factory price-Tianfuchenglai-75-10
$1080.00now $880.00 piece19%OFF
VMC1270 high-speed machining center with AC servo technology stepless speed change of the spindle-tianfuchenglai112
$75800.00now $71000.00 unit6%OFF
Hot use G4250 metal band sawing machine for machine house and factory metal process machining tool with factory price-Tianfuchenglai111
$13600.00now $12000.00 unit12%OFF
Industrial supply CK6150X1000 CNC Lathe machine for metal products cutting tunning process with factory price-Tianfuchenglai110
$17800.00now $16500.00 unit7%OFF
4×8 Egg Tray Production machine Line with single-layer dryer with factory price-Tianfuchenglai-73-1
$99900.00now $96000.00 set4%OFF
30 ton homogenizing furnace group for aluminum bar billets aluminum profile producing industrail machine line with factory price-Tianfuchenglai 111
$338000.00now $298000.00 set12%OFF
- Silicon carbide crucible and melting furnace
- High temperature coating curing oven machine
- Ultrasonic/high pressure cleaning and drying machine line
- Cold Chamber Die Casting machine
- Hydraulic Press Machine & CNC machine
- Automatic Sandblasting Blaster Machine
- Steel coil slitting machine
- Printing machine
- Packaging machine
- Other machine line
- Contact US
Your cart is currently empty.